As a mold sales, need to study mold structure design too

 A set of high-quality molds not only requires good processing equipment and skilled mold manufacturing workers, but also another very important factor is to have a good mold design. Especially for complex molds, the quality of mold design accounts for more than 80% of the mold quality. An excellent mold design is: under the premise of meeting the customer's requirements, the processing cost is low, the processing difficulty is small, and the processing time is short.


To achieve this, it is necessary not only to fully digest the customer's requirements, but also to understand the injection molding machine, mold structure, processing technology and the mold factory's own processing capabilities. Therefore, to improve the level of mold design, the following points should be achieved:


1. Understand every detail in each set of mold design and understand the purpose of each part in the mold.


2. Refer to previous similar designs when designing, and understand the situation during its mold processing and product production, and learn from the experience and lessons.


3. Learn more about the working process of the injection molding machine to deepen the relationship between the mold and the injection molding machine.


4. Go to the factory to understand the processing technology of the processed products and recognize the characteristics and limitations of each processing.


5. Understand the mold trial results and mold modification of the mold designed by yourself, and learn lessons.


6. Try to use the mold structure that was successful in the past when designing.


7. Learn more about the impact of water entering the mold on the product.


8. Study some special mold structures and understand the latest mold technology.

评论

发表评论

此博客中的热门博文

Molding Conditions of Injection Molding Machine (Part 2)

 1. Filling pressure In injection molding conditions, filling pressure refers to the pressure to fill the resin into the mold, also known as primary pressure. The unit is MPa or kgf/cm2. That is the unit of pressure. There are also some injection molding machines that set the maximum injection pressure to 100%, and then adjust the injection molding conditions by changing the percentage. (Example: 35%) If the filling pressure is too low, poor filling (underfill) will occur. If the filling pressure is too high, the parting surface may be momentarily opened by the pressure, and burrs may appear around the molded product. Sometimes poor release occurs. 2. Injection speed Injection speed refers to the speed at which molten plastic fills the mold. The unit is mm/s. When considering injection volume per unit of time, it may be stated as "injection rate", in which case the unit is cm3/s. If the injection speed is too slow, filling defects may occur; if the injection speed is too fast...
阅读全文

How to choose the original positioning parts of injection mold custom processing workpiece?

 1. Injection mold custom processing workpiece to plane positioning According to the number of degrees of freedom restricted by the plane, it can be divided into three types: The main support surface restricts the positioning plane of the three degrees of freedom of the workpiece, and is often used for the positioning surface of the workpiece with relatively high precision. The guide support surface is a positioning plane that limits the two degrees of freedom of the workpiece, and is often made into a narrow and long surface. The thrust support surface is a plane that limits one degree of freedom. In order to ensure accurate positioning, the area of the plane is often made as small as possible. 2. Injection mold custom processing workpiece is positioned with a round hole Long pins limit 4 degrees of freedom; short pins limit 2 degrees of freedom. 3. Injection mold custom processing workpiece outside cylindrical surface positioning The positioning datum is the centerline of the out...
阅读全文

2K tooling on Injection molding

图片
 Injection molding is a process that was developed based on microfabrication techniques such as LIGA, but there are of course many other methods. The LIGA process is to first produce a model required for injection molding, which is commonly known as "mold", and then pour liquid plastic into the mold, and finally separate it to form the final required product. For example, some Automotive parts have too many products. Injection mold processing is to add plastic to the mold first, and then the mold is continuously rotated along two vertical axes and heated. The plastic in the mold is gradually and evenly coated and melted and adhered to the entire cavity of the mold cavity under the action of gravity and heat energy. On the surface, it is formed into the desired shape, and it is made by cooling and setting.
阅读全文