How to know Mold Constructions

 羧甲基纤维素
cn |cellulose nitrate |硝酸纤维素 
cpe |chlorinated polyethylene|氯化聚乙烯 
cpvc |chlorinated poly(vinyl chloride) |氯化聚氯乙烯
ep |epoxy, epoxide|环氧树脂
epm |ethylene-propylene polymer |乙烯/丙烯共聚物
eps |expanded polystyrene |可发性聚苯乙烯
eva |ethylene/vinyl acetate |乙烯/醋酸乙烯共聚物
hdpe |high-density polyethyleneplastics |高密度聚乙烯
hips |high impact polystyrene |高抗冲聚苯乙烯
k胶| styrene- butadiene |苯乙烯/丁二烯共聚物
lcp |liquid crystal polymer |液晶聚合物
ldpe |low-density polyethyleneplastics |低密度聚乙烯)
lldpe |linear low-density polyethylene |线型低密聚乙烯
lmdpe |linear medium-density polyethylene |线型中密聚乙烯
mbs |methacrylate-butadiene-styrene |甲基丙烯酸/丁二烯/苯乙烯共聚物




评论

发表评论

此博客中的热门博文

Molding Conditions of Injection Molding Machine (Part 2)

 1. Filling pressure In injection molding conditions, filling pressure refers to the pressure to fill the resin into the mold, also known as primary pressure. The unit is MPa or kgf/cm2. That is the unit of pressure. There are also some injection molding machines that set the maximum injection pressure to 100%, and then adjust the injection molding conditions by changing the percentage. (Example: 35%) If the filling pressure is too low, poor filling (underfill) will occur. If the filling pressure is too high, the parting surface may be momentarily opened by the pressure, and burrs may appear around the molded product. Sometimes poor release occurs. 2. Injection speed Injection speed refers to the speed at which molten plastic fills the mold. The unit is mm/s. When considering injection volume per unit of time, it may be stated as "injection rate", in which case the unit is cm3/s. If the injection speed is too slow, filling defects may occur; if the injection speed is too fast...
阅读全文

How to choose the original positioning parts of injection mold custom processing workpiece?

 1. Injection mold custom processing workpiece to plane positioning According to the number of degrees of freedom restricted by the plane, it can be divided into three types: The main support surface restricts the positioning plane of the three degrees of freedom of the workpiece, and is often used for the positioning surface of the workpiece with relatively high precision. The guide support surface is a positioning plane that limits the two degrees of freedom of the workpiece, and is often made into a narrow and long surface. The thrust support surface is a plane that limits one degree of freedom. In order to ensure accurate positioning, the area of the plane is often made as small as possible. 2. Injection mold custom processing workpiece is positioned with a round hole Long pins limit 4 degrees of freedom; short pins limit 2 degrees of freedom. 3. Injection mold custom processing workpiece outside cylindrical surface positioning The positioning datum is the centerline of the out...
阅读全文

2K tooling on Injection molding

图片
 Injection molding is a process that was developed based on microfabrication techniques such as LIGA, but there are of course many other methods. The LIGA process is to first produce a model required for injection molding, which is commonly known as "mold", and then pour liquid plastic into the mold, and finally separate it to form the final required product. For example, some Automotive parts have too many products. Injection mold processing is to add plastic to the mold first, and then the mold is continuously rotated along two vertical axes and heated. The plastic in the mold is gradually and evenly coated and melted and adhered to the entire cavity of the mold cavity under the action of gravity and heat energy. On the surface, it is formed into the desired shape, and it is made by cooling and setting.
阅读全文